how to adjust electric rv awning

How To Adjust an Electric RV Awning- A Quick Guide

Introduction

Did you install a new electric awning in your RV? Not sure how to adjust it?? 

Don’t stress because we’ve got your back, buddy.

So how to adjust electric RV awning?

Well, your electric awning will need different adjustments based on your requirements and ease. You can adjust the RV awning arms by fixing the fabric. You can also adjust the RV awning lead rails as it can be too loose at times. Furthermore, you can adjust the awning pitch to accommodate water runoff.

This was just the basics of adjustment. Head over to our segment to know in detail about the adjustments. Also how to make them for a better experience with your RV awning.  

Adjusting electric RV awning – 3 Quick & Easy Adjustments

Adjusting an electric RV awning can be trickier than adjusting a manual one. Even though installing an electric RV awning is easier.

But you need to align your electric RV awning according to your requirements. Here’s how you can adjust your awning in different ways-

Adjusting RV awning arms  

You can adjust your electric RV awning arms by fixing the canvas fabric. The canvas or vinyl can often become misaligned or stretched either because of wind or rain. 

This results in the awning being winded up crooked on the roller tube. Hence the arms fail to line up and align with the upper arm rails. This happens when the awning is closed. 

First of all, extend the electric RV awning. The awning is usually connected with the RV via the awning track. You’ll find a smaller screw also known as the slider set screw at each end of the track. This screw is present to avoid the awning from sliding to the other side. 

Now, you need to identify the direction where the awning arm rail needs to be moved or shifted. If you feel like the upper arm rail needs to be shifted to the left side, simply remove the left screw. And then pull the awning track towards the left. Do the opposite for the right side. 

Make sure to move the awning only half-inch at a time and not too fast. This way, you’ll get a more accurate result and right where you want it.

After you’ve adjusted the awning to your desire, reinstall the set screw. And you’re done with the adjustment. 

Adjusting loose RV awning lead rails

You may find your RV awning lead rails not fully retracting to the awning box. Now, this is a common electric awning issue and you can quite easily make adjustments here. This happens because the lead rail may be loose. 

For making the adjustments, here’s what you’ll need-

  • 7/16 inch wrench/socket
  • Rubber mallet

To adjust the lead rails, begin by closing the center of the rail properly. Make sure the rails are tightly closed to the awning box. At this point, you’ll need to reset the motor to fix the rail. Moreover, use the wrench or socket and the rubber mallet to close the ends of the rail tighter. 

If you still find the lead rails loose, open up the awning about ¾ the way and switch off the power. Now loosen the nut of the rails and slide each arm ⅛ inch towards the end of the lead rail. 

Tighten the nut and close the awning after this and check for the adjustments. Your awning lead rails should be tight enough and will properly retract when closed. 

Make sure to adjust both sides of the lead rail. Even if just one side of the lead rails is loose, tighten both ends to ensure proper adjustment. If you do not adjust both sides, the rail will track off the center and not close properly. This can cause unwanted damage and accidents.

By the way, here are our top choices of rubber mallet for RV awnings-

Adjusting RV awning pitch

The fabric roller tube assembly may often be higher than the awning’s rail. If this happens, the awning pitch will fault to perform its job. The pitch usually helps to accommodate water runoff. 

So if you want a steeper awning pitch, the fabric roller tube assembly needs to be lowered. So to lower the assembly, here’s what you need to do-

Extend the awning fully and then loosen the adjustment knob of the adjustable pitch arm assembly. We’re talking about the bottom arm here. 

Now hold the arm assembly in place and tighten the adjustable knob to set the pitch. It should be done just the way you want it.

Now it is important to place one side of the hardware in a reliable position as you adjust the pitch. This will help avoid water pooling on the fabric. This in turn can result in serious accidents and injuries. 

FAQs

Question: Is it safe to tie down RV awning?

Answer: Most electric awnings have a wind sensor on them. It needs to be turned off. If the awning tries to roll up when tying them down, it could lead to damage in the motor or awning arms. So it’s not very safe.

Question: Does RV awning flapping cause damage?

Answer: Over time, constant flapping can cause huge damage to the awning. It can tear the bead that fastens the fabric to the rail of the RV. In this case, you’ll need to replace the awning. 

Question: How to protect RV awnings during high winds?

Answer: If the winds are moderate, you can hook an awning storm strap over the awning and fix it on either side to pin the awning down. This protects the awning from high wind. 

Conclusion

That’s all from our side. By now you should be able to know how to adjust electric RV awning and adjust this all on your own. 

We hope all your concerns relating to RV awning adjustments have been cleared now. 

5 Best RV Awning Tie Downs (Reviews & Buying Guide)

Best RV Awning Repair Tape

As an Amazon Associate I earn from qualifying purchases.

Leave a Comment

Your email address will not be published. Required fields are marked *

x
Scroll to Top